If you’re a homeowner, there’s a good chance you own a Dewalt 20v trimmer. They’re some of the most popular models on the market, and for good reason – they’re tough and reliable.
However, even the best tools can have problems from time to time. In this blog post, we’ll take a look at 10 common issues with the Dewalt 20v trimmer – and how to fix them!
Dewalt 20v Trimmer Problems
- The trimmer won’t start: This could be due to a faulty spark plug, or an issue with the fuel system. To diagnose and fix this problem, it’s best to consult a service technician.
- Difficulty starting up after a period of disuse: If you haven’t used the trimmer in a while, the carburetor may need adjusting to get it back up and running properly. Again, consulting a professional is recommended for this kind of task.
- Spool issues: If your line isn’t feeding correctly out from the spool, there could be an issue with the spool itself or with how its tensions are set. Adjusting these will usually solve any problems here.
- Engine cuts out during use: This could be due to an old or faulty spark plug, or the carburetor might need adjusting. In any case, it’s best to have a service technician take a look at this one.
- Excessive vibration: If you’re experiencing excessive vibrations while using your trimmer, there may be a problem with the drive shaft bearings or engine mounts that need to be addressed by a professional.
- Too much smoke coming from the muffler: This is usually caused by a dirty air filter, which can be easily replaced if needed.
- The trimmer won’t idle: A sticking throttle cable could be causing this issue – try checking and lubricating it if necessary.
- Trimmer runs too rich: This could be caused by an issue with the carburetor or a bad fuel mixture, both of which can be fixed by tuning the carburetor or adjusting the air/fuel ratio.
- Gearbox issues: If you’re having problems shifting gears, there may be something wrong with the gearbox itself – have a technician take a look at this one.
- Ignition system problems: A faulty ignition coil or spark plug could be causing your trimmer to not start properly – replacing these parts should do the trick!
Dewalt 20v Trimmer won’t start solutions
- Check the fuel level: A common reason why your Dewalt 20v trimmer won’t start is that it doesn’t have enough fuel in the tank. Make sure that you check the fuel level and top off if needed before attempting to restart the trimmer.
- Change spark plug: If there is sufficient fuel, but still no response when you try to start your trimmer, then chances are that the spark plug has become faulty over time. Replacing the spark plug should resolve any issues with starting up your trimmer again.
- Clean air filter: Another possible cause of not starting could be a dirty or clogged air filter preventing airflow from reaching the engine. Cleaning out this filter should allow the engine to start properly again.
- Check battery: Lastly, make sure that your trimmer is getting enough power from its battery. If the battery isn’t charged or has run out of charge completely, then it could be a reason why your Dewalt 20v trimmer won’t start. Try charging the battery fully and see if it fixes the issue.
Hopefully, these solutions will help you get your trimmer up and running again.
Dewalt 20v trimmer shuts down while in use solutions
If your Dewalt trimmer is shutting down while in use, there are several possible solutions.
- First, check that the battery is fully charged and that all connections to the battery are secure. If the battery is not fully charged or has loose connections, it can cause the trimmer to shut down unexpectedly.
- Second, make sure that you’re using a compatible blade for your model of trimmer. Different models may require specific blades and using an incompatible one could lead to sudden shutdowns.
- Third, try cleaning any dirt or debris from inside the motor or around its air vents. This can help prevent overheating which can be a common cause of unexpected shutdowns in power tools like trimmers.
Finally, if all else fails, it may be time to take your trimmer in for repairs. An experienced technician can diagnose and repair the problem quickly and safely so you can get back to trimming without fear of unexpected shutdowns.
Dewalt 20v trimmer battery problems solutions
If you are having trouble with your Dewalt 20v trimmer battery, there are a few potential solutions that can help resolve the issue.
- Ensure Your Battery is Fully Charged – Make sure that your battery has been fully charged before use. If it hasn’t been recently, plug the charger in for at least 8 hours to give it a full charge.
- Clean All Connections – Make sure all connections between the battery and the device are clear of dirt or debris, as this can affect performance and cause problems like slow charging, low power output, and even failure altogether.
- Check Power Settings – Some models of Dewalt 20v trimmers have adjustable settings for power output. If you have reduced the power output, try increasing it to see if this makes a difference in your battery’s performance.
- Replace Your Battery – In some cases, the issue may be due to an aging or faulty battery. If this is the case, replacing the battery with a new one can solve the problem.
- Seek Professional Assistance – If none of these solutions resolves your issue, there could be something else wrong with your trimmer that requires professional help. Contact a local technician or take your device to an authorized service center for further inspection and repair if necessary.
Dewalt 20v trimmer vibrating while in use solutions
- Make sure that the trimmer is properly assembled and that all parts are securely tightened.
- Check for any dirt, grass, or debris build-up around the cutting head and ensure that it’s clear of obstruction.
- Ensure that you have the correct blade size installed for your specific model of the trimmer and check to make sure it’s not worn down or broken in any way.
- Lubricate any moving parts with oil as necessary to reduce friction and improve performance
- If the vibration persists, replace the shaft assembly with a new one if applicable to your model of Dewalt 20v trimmer.
- Tighten the screws on the trimmer head to help reduce the amount of vibration coming from the motor.
- Inspect the line for damage, replace it if necessary and make sure that it’s wound properly around the spool.
- Finally, consider replacing any worn or faulty components with new ones as specified by your model of the Dewalt 20v trimmer manual.
By following these steps, you should be able to identify and solve most of the problems associated with your Dewalt trimmer vibrating while in use. If all else fails, it may be time to take your tool to a professional repair shop or contact Dewalt directly in order to get assistance with troubleshooting and repairs.
Dewalt 20v trimmer head stuck solutions
The first step in troubleshooting a Dewalt trimmer head that is stuck is to inspect the trimmer head assembly for any obstructions or damage.
If you find an obstruction, simply remove it and try starting the trimmer again. If there appears to be no visible blockage, then it’s time to take a closer look at the inside of your machine.
Start by removing the air filter cover and inspecting the filter itself for any buildup of dirt or debris. If necessary, clean or replace the air filter before reassembling the housing.
It is also important to check the spark plug for any signs of corrosion or wear, as this can prevent your engine from running properly. Replace if needed and make sure to re-gap the plug.
Next, inspect the starter for any signs of damage or wear. If there is a problem, replace the starter before attempting to start your trimmer again.
Finally, make sure all connections are tight and secure and that the carburetor bowl is clean and free from debris. After you’ve finished inspecting all components, try starting the trimmer head again—if it still fails to start, it may be time to call in a professional repair service.
Leave a Reply